Peerless Industries TV Mount HLG452 002 User Manual

Installation and Assembly  
Flat-Panel Base Lock-Down Kit For Philips Display  
Models  
Models: HLG452-002, HLG452-002-Q10  
Maximum Display Weight: 100 lb (45.35 kg)  
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com  
ISSUED: 09-04-08 SHEET #: 090-9150-3 10-05-09  
 
Installation Option 1 (Fasteners)  
DISPLAY MODEL HOLE PATTERNS  
SBP240M/27  
A.  
42HF7945D/27  
37HFL5560D/27  
42HFL55860D/27  
42HFL7945D/27  
42HFL7580A/27  
52HFL5580D/27  
B.  
C. 26HFL5830D/27  
32HFL5460D/27  
32HFL5860D/27  
32HFL7560D/27  
32HF7965D/27  
32HFL7965D/27  
SCREWS SUPPLIED BY DISPLAY  
MANUFACTURER  
SCREWS SUPPLIED BY DISPLAY  
MANUFACTURER  
SCREWS SUPPLIED BY DISPLAY  
MANUFACTURER  
Use lock-down plate (A) as a template to mark location  
of holes, point 1 and point 2, approximately 7" apart on  
table. Drill two holes using a 1/4'' drill bit.  
Slide two 1/4-20 x 1 3/4" bolts (B) through slots as  
shown below.  
2
1
NOTE: 2 1/4" carriage bolts (ACC939) are available  
for use with thicker mounting surfaces.  
7"  
B
(178 mm)  
POINT 2  
POINT 1  
A
TABLE TOP  
3 of 6  
ISSUED: 09-04-08 SHEET #: 090-9150-3 10-05-09  
For customer care call 1-800-729-0307 or 708-865-8870.  
 
Attach lock-down plate to display base bottom using  
screws provided by manufacturer. Refer to page three  
for lock-down plate/ display base stand hole pattern.  
NOTE: Remove existing rubber feet from display base  
that interfere with the lock-down plate.  
Hand tighten slope nut (D) through 1/4-20 x 1 3/4"  
screw bolt (B) until snug against bottom of desktop  
surface. Thread another slope nut (D) upside-down,  
about two turns from first slope nut (D). Insert a open  
box wrench between both slope nuts (D) and tighten.  
NOTE: Avoid jamming both slope nuts (D) together,  
doing so may make it difficult to remove slope nut  
used for tightening first slope nut (D). After slope nut is  
secure remove bottom slope nut and add plastic cap  
(C) as shown in figure 4.2. Repeat with remaining  
1/4-20 x 1 3/4" screw bolt (B).  
3
4
DISPLAY BASE STAND  
RUBBERFEET  
BOTTOM OF DESKTOP  
A
SCREWS SUPPLIED BY  
B
B
MANUFACTURER  
D
TIGHTENING  
SLOPE NUT  
NOTE: Display base stand and mounting  
hole locations may appear different than  
illustrated.  
C
FIG 4.1  
FIG 4.2  
4 of 6  
ISSUED: 09-04-08 SHEET #: 090-9150-3 10-05-09  
For customer care call 1-800-729-0307 or 708-865-8870.  
 
Installation Option 2 (Adhesive Strips)  
DISPLAY MODEL HOLE PATTERNS  
Attach lock-down plate to display base bottom using  
screws provided by manufacturer. Refer to lock-down  
plate/ display base stand hole pattern.  
SBP240M/27  
A.  
NOTE: Remove existing rubber feet from display base  
that interfere with the lock-down plate.  
42HF7945D/27 HOLE PATTERN SHOWN  
DISPLAY BASE STAND  
SCREWS SUPPLIED BY DISPLAY  
MANUFACTURER  
42HF7945D/27  
B.  
37HFL5560D/27  
42HFL55860D/27  
42HFL7945D/27  
42HFL7580A/27  
52HFL5580D/27  
RUBBERFEET  
A
SCREWS SUPPLIED BY  
MANUFACTURER  
NOTE: Display base stand and mounting  
hole locations may appear different than  
illustrated.  
SCREWS SUPPLIED BY DISPLAY  
MANUFACTURER  
C. 26HFL5830D/27  
32HFL5460D/27  
32HFL5860D/27  
32HFL7560D/27  
32HF7965D/27  
32HFL7965D/27  
SCREWS SUPPLIED BY DISPLAY  
MANUFACTURER  
5 of 6  
ISSUED: 09-04-08 SHEET #: 090-9150-3 10-05-09  
For customer care call 1-800-729-0307 or 708-865-8870.  
 
Clean bottom of lock-down plate (A) with rubbing alcohol. Spray bottom of lock-down plate (A) only where tape will  
be applied, with 3M rubber and vinyl #80 spray adhesive. Pull apart the four adhesive strips (E) and remove red  
backing film on both sides. Wait at least 4 minutes to dry before applying adhesive strip (E). Attach adhesive  
strips (E) firmly to bottom of lock-down plate (A) as shown below.  
4
CLEAN WITH  
RUBBING  
ALCOHOL  
DRIED 3M  
RUBBERAND  
VINYL #80 SPRAY  
ADHESIVE  
E
A
Clean desk surface with rubbing alcohol. Use 3M rubber and vinyl #80 spray adhesive (not supplied) on the mounting  
surface area only. NOTE: Spray adhesive will not remove easily. Wait at least 4 minutes to dry before removing tape  
backing from lock-down plate (A) and placing firmly on surface. NOTE: There is a recommended 72 hour cure time for  
tape on lock-down plate (A).  
NOTE: Once tape backing is removed be careful not to touch the sticky surface of the tape with fingers, as this can  
cause the tape to lose some of its holding power.  
NOTE: After application of tape on lock-down plate (A), the bond strength will increase as the adhesive flows onto the  
surface.  
At room tempurature, approximately 50%  
of the ultimate strength will be achieved  
after 20 minutes, 90% after 24 hours,  
and 100% after 72 hours. In some cases,  
bond strength can be achieved more quickly  
by exposure to elevated temperatures  
(e.g. 150°F [66°C] for 1 hour).  
DISPLAY BASE STAND  
DRIED 3M RUBBERAND  
VINYL #80 SPRAY  
ADHESIVE (not supplied)  
DESK SURFACE  
NOTE: Display base stand may appear  
different than illustrated.  
6 of 6  
ISSUED: 09-04-08 SHEET #: 090-9150-3 10-05-09  
For customer care call 1-800-729-0307 or 708-865-8870.  
 

Pelco Home Theater Server MX4004 User Manual
Pelican Video Game Controller PL 678 User Manual
Philips TV Cables SWA2138W User Manual
Pioneer Musical Toy Instrument DDJ SR User Manual
Pioneer Speaker System HTP 500 User Manual
Polaroid Portable DVD Player PDM 0744M User Manual
Polaroid Tablet 7 INTERNET TABLET User Manual
Poulan Lawn Mower 191491 User Manual
Poulan Trimmer 530086413 User Manual
Power Acoustik Speaker REP 12 User Manual